Product ID:E 260 H BLACK M.C. PLASTIC MOLDING
MSDS Date:07/21/1992
FSC:9330
NIIN:01-102-1661
MSDS Number: BNMPT

FIBERITE CORP SUB OF BEATRICE FOODS

501 W 3RD STREET
WINONA, MN 55987-2854
US

Emergency Phone: 507-452-8051/800-424-9300(CHEMTREC)

Info Phone: 507-452-8051

Cage: 07314

FIBERITE CORP SUB OF BEATRICE FOODS

WINONA, MN 55987-2854 US

Telephone: 507-452-8082/507-452-8092

Cage: 07314

BORON TRIFLUORIDE-ETHYLAMINE COMPLEX

CAS: 75-23-0

RTECS: KQ8060000

ANTIMONY TRIOXIDE (SARA III)

CAS: 1309-64-4

RTECS: CC5650000

OSHA PEL 0.5 MG/M3 (SB)

ACGIH TLV: 0.5 MG SB/M3; 9192

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

EPOXY RESIN

FIBERGLASS

OSHA PEL 15 MG/M3(TOTAL DUST)

ACGIH TLV: 10 MG/M3 (DUST)

LD50 LC50 Mixture:NOT SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:IRRITATION OF SKIN AND EYES, POSSIBLE
DERMATITIS OR ALLERGY SENSITIZATION, RESPIRATORY TRACT IRRITATION,
MUCOUS MEMBRANE IRRITATION, SKIN LESIONS KNOWN AS "ANTIMONY
MEASLES", CHRONIC INHALATION MAY RE SULT IN LUNG DISEASE AND
TUMORS, LIVER DAMAGE AND CHANGES IN THE BLOOD.
Explanation of Carcinogenicity:PRODUCT CONTAINS NO INGREDIENTS
CURRENTLY CLASSIFIED AS CARCINOGENIC BY NTP, IARC OR OSHA.
Effects of Overexposure:EYE IRRITATION, SKIN IRRITATION, SKIN LESIONS,
RESPIRATORY TRACT IRRITATION, MUCOUS MEMBRANE IRRITATION, LUNG
DISEASE, TUMORS, LIVER DAMAGE, BLOOD CHANGES.
Medical Cond Aggravated by Exposure:EXISTING ALLERGIES MAY BE
AGGRAVATED.

First Aid:INHALATION: REMOVE TO FRESH AIR. PROVIDE OXYGEN IF NECESSARY.
IF NOT BREATHING, RESUSCITATE. CALL A PHYSICIAN. EYES: IRRIGATE
WITH WATER FOR 15 MINUTES. SEEK MEDICAL ATTENTION. SKIN: WASH
THOROUGHLY W ITH SOAP AND WATER. SEEK MEDICAL ATTENTION. INGESTION:
INDUCE VOMITING IF LARGE AMOUNTS ARE INGESTED. NEVER GIVE ANYTHING
BY MOUTH TO OT INDUCE VOMITING ON AN UNCONSCIOUS VICTIM. SEEK
MEDICAL ADVICE.

Flash Point:NON-FLAMMABLE
Lower Limits:NOT GIVEN
Upper Limits:NOT GIVEN
Extinguishing Media:CARBON DIOXIDE, FOAM, DRY CHEMICAL, WATER
Fire Fighting Procedures:DISSIPATE HEAT BY SPREADING MATERIAL APART AND
DOUSING WITH WATER. CONTAIN EMISSIONS USING LOCAL EXHAUST.
Unusual Fire/Explosion Hazard:FIRE RELEASES TOXIC SMOKE AND FUMES.
HAZARDOUS POLYMERIZATION CAN OCCUR UPON EXCESSIVE HEATING.

Spill Release Procedures:CONTAMINATED MATERIAL SHOULD BE PICKED UP AND
DISPOSED OF PROPERLY.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE AT OR BELOW 65 DEG F.
Other Precautions:AVOID SKIN CONTACT. WHEN PROCESSING AT ELEVATED
TEMPERATURES, PROVIDE ADEQUATE VENTILATION TO CONTROL PROCESSING
FUMES AND VAPORS.

Respiratory Protection:USUALLY NOT NEEDED USE NIOSH APPROVED RESPIRATOR
IF EXPOSURE LIMITS ARE EXCEEDED. IN THE ABSENCE OF ADEQUATE GENERAL
OR LOCAL VENTILATION, PROVIDE NIOSH APPROVED RESPIRATORS TO
MINIMIZE EXPOSURE TO GA S, VAPORS OR FUMES RELEASED DURING WORK
Ventilation:LOCAL EXHAUST RECOMMENDED
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:SAFETY GLASSES AND FACE SHIELD
Other Protective Equipment:IMPERVIOUS AND CLEAN BODY-COVERING
Work Hygienic Practices:IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE,
HANDLE WITH CARE AND AVOID UNNECESSARY PERSONAL CONTACT.
Supplemental Safety and Health
THIS PRODUCT CONTAINS UNCURED RESINS. CURING SHOULD ONLY BE DONE IN
WELL-VENTILATED OR CLOSED SYSTEMS.

HCC:N1
Boiling Pt:B.P. Text:NOT GIVEN
Melt/Freeze Pt:M.P/F.P Text:NOT GIVEN
Vapor Pres:NOT GIVEN
Vapor Density:NOT GIVEN
Spec Gravity:1.86 - 1.92
Evaporation Rate & Reference:NOT GIVEN
Solubility in Water:NOT GIVEN
Appearance and Odor:BLACK MOLDING MATERIAL; SLIGHT ODOR
Percent Volatiles by Volume:< 1%

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, STRONG BASES, STRONG OXIDIZERS
Stability Condition to Avoid:EXTREME TEMEPRATURES
Hazardous Decomposition Products:DENSE SMOKE, ACRID VAPORS AND FUMES,
HYDROCARBONS OF VARIABLE COMPOSITION, CARBON MONOXIDE, CARBON
DIOXIDE, OXIDES OF N
Conditions to Avoid Polymerization:HAZARDOUS POLYMERIZATION CAN OCCUR
WITH RAPID OR EXCESSIVE HEATING.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS. QUESTIONS CONCERNING DISPOSAL SHOULD BE
DIRECTED TO ICI FIBERITE'S SAFETY, HEALTH, AND ENVIRONMENTAL
AFFAIRS DEPARTMENT FOR EVALUATI ON ON A CASE-BY-CASE BASIS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.